EMT Practice Test

1. Question Content...

---

Question1: Toxic releases in RBI are only addressed when they affect

Question2: Through __________________, inspection activities are focused on higher risk items and away from lower risk items.

Question3: __________ is not a substitute for a process hazards analysis (PHA) or HAZOP

Question4: Probability side of the risk equation is normally managed by

Question5: The programme that focused on maintaining the mechanical integrity of pressure equipment items and minimizing the risk of loss of containment due to deterioration

Question6: The program that is focused on understanding failure modes, addressing the modes and therefore improving the reliability of equipment and process facilities.

Question7: _________ are the primary inputs into the probability of failure evaluation.

Question8: The risk prior to mitigation activities

Question9: Who should be consulted to define the equipment deterioration mechanisms, susceptibility and potential failure modes?

Question10: The data validation step stresses the need for a knowledgeable individual.

Question11: _________________curves are referred for the deterioration mechanism for carbon and low ally steel materials.

Question12: Following will cover the functional failures except

Question13: FILL BLANK
RBI as an integrated management tool that complements___________

Question14: The following types of pressurized equipment and associated components covered by RBI

Question15: The reduction in the ability of a component to provide its intended purpose of containment of Fluids

Question16: The ability to state the rate of deterioration precisely is affected by the following except

Question17: Termination of the ability of a system, structure, or component to perform its required function of containment of fluid (le loss of containment)

Question18: In process plants are established to detect and evaluate deterioration due to in service operation.

Question19: The primary audience for RP 580 is

Question20: Following are the common mechanical deterioration mechanisms except

Question21: The amount and type of codes and standards used by a facility can have

Question22: ____________ are often necessary to establish susceptibility of equipment to stress corrosion cracking.

Question23: Act of mitigating a known risk to a lower level of risk.

Question24: Consequence is always __________ for safety aspects

Question25: ______________ provides a consistent methodology for assessing the optimum combination of methods and frequencies.

Question26: Qualitative consequence analysis of failure can be estimated separately for each unit, system, equipment group or individual equipment item.

Question27: If a QRA has been prepared for a process unit, the analysis can borrow extensively from this effort.

Question28: When in accurate or insufficient failure data exists on the specific equipment item for quantitate probability of failure analysis then

Question29: When equipment has low deterioration rates as an inspector what you decide in lieu of internal inspection.

Question30: Following are not the residual risk factors for loss of containment.

Question31: Risk presented in quantitative risk analysis as a

Question32: A RBI analysis shares many of the techniques and data requirements with a ____________.

Question33: The risk assessment programme which focuses on process unit design and operating practices and their adequacy given the unit's current or anticipated operating conditions

Question34: RBI is focused on a systematic determination of

Question35: The type of failure mode that likely to occur due to pitting

Question36: Hazard identification in a RBI analysis generally focuses on identifiable failure mechanisms in the equipment (inspectable causes) but does not explicitly deal with

Question37: The suitability and current condition of the equipment within the current operating envelope will determine the ______________ of the equipment from one or more deterioration mechanisms.

Question38: If multiple inspections have been performed, which inspection may best reflect current operating conditions?

Question39: Who can provide useful input (such as the spectrum of process conditions, injection points etc.) To aid materials specialists in the identification of deterioration mechanisms and rates

Question40: An analytical tool that organizes and characterizes potential accidents in a logical and graphical manner

Question41: Act of mitigating a known risk to a lower level of risk.

Question42: Damage mechanisms where deterioration rates are immeasurable or unknown are

Question43: Sec occurs when equipment is exposed to environments

Question44: When some risk identified as acceptable then one of the following is not required.

Question45: Results of quantitative consequence analysis are usually expressed in

Question46: ____________deals with total risk than with risk involve only with the equipment.

Question47: FILL BLANK
_________ produces inspection and maintenance plans for equipment that should be implemented to provide ____________

Question48: For a typical inspection program, if excessive inspection is applied then,

Question49: _____________ represents the next generation of inspection approaches and interval setting, recognizing that the ultimate goal of inspection is the safety and reliability of operating facilities

Question50: The type of failure mode that likely to occur due thinning

Question51: Limitation of any negative consequence or reduction in probability of a particular event

Question52: Following is the unit of measure of consequence that is least developed among those currently used for RBI assessment.

Question53: Occurrence of a particular set of circumstances, is called an

Question54: RBI requires the commitment and cooperation of the

Question55: Outcome of an event

Question56: Small hole, crack or rupture are examples of

Question57: Results from quantitative analysis logic models are validated by

Question58: A process to assess risks, to determine if risk reduction is required and to develop a plan to maintain risks at an acceptable level

Question59: Depending on the methodology employed in qualitative analysis, the categories may be described with words such as

Question60: The event may be

Question61: In most consequence evaluations, a key element in deter-mining the magnitude of the consequence is

Question62: Deterioration rates can be expressed in terms of

Question63: FILL BLANK
RP 580 significantly targeted at the application of RBI in the ______________ and ___________ industry

Question64: The RBI program for environmental consequences, typically focuses

Question65: Following are the critical variables for deterioration mechanism except

Question66: A physical condition or a release of a hazardous material that could result from component failure and result in human injury or death, loss or damage, or environ- mental degradation

Question67: Consequence analysis will aid in preparation of

Question68: The type of failure mode that likely to occur due to SSC

Question69: Risk presented in qualitative risk analysis as

Question70: FILL BLANK
RP 580 is intended to promote consistency and quality in identification, assessment and management of risks pertaining to ____________, which could lead to _______________

Question71: Other functional failures are usually covered within

Question72: Is key to performing deterioration mechanism identification